Category 6+ enhanced performance – 4–pair F/UTP design verified to TIA 568.C.2 Category 6 standards for high–speed data applications.
Plenum–rated construction – CMP–rated with Flamarrest® low–smoke PVC outer jacket, tested to NFPA 262, UL 910 (Plenum), FT6 and IEC 60332–1–2 for use in environmental air spaces.
Shielded for noise immunity – Overall polyester and aluminum/poly laminate shield with 100% coverage and a 24 AWG solid tinned copper drain wire to help reduce EMI and RFI.
Bonded–pair design – Bonded conductor pairs withstand higher pulling tension and tighter bend radii, helping the cable survive tough installations without degrading performance.
Central X–spline separator – Patented central spline and polyester tape separator keep pairs physically separated, enhancing crosstalk performance and maintaining consistent electrical characteristics.
Solid bare copper conductors – 23 AWG solid bare copper conductors provide stable signal transmission and low insertion loss over long distances.
High–quality insulation – Fluorinated ethylene propylene (FEP) insulation on conductors supports reliable electrical performance in plenum environments.
Durable outer jacket – Flamarrest® low–smoke PVC jacket with a nominal diameter of 0.285 in provides robust mechanical protection while remaining easy to route.
Wide temperature tolerance – Rated for storage from -4°F to 167°F, installation from 41°F to 122°F, and operation from -4°F to 167°F to handle varied environmental conditions.
Installation–friendly – Supports a recommended maximum pulling tension of 25 lb, a minimum 1 in bend radius for the minor axis, and a 3 in minimum bend during installation.
Lightweight 1000 ft box – Supplied in a 1000 ft pull box with an approximate weight of 49 lb for manageable handling on site.
Standards compliant – Meets NEC Article 800 CMP and CEC CMP requirements, UL Verified to Category 6, and compliant with China RoHS (MII Order #39) and California Prop 65.
Non–gel construction – Dry core design avoids messy gels, tapes, or powders, simplifying pulls and terminations in indoor or indoor/outdoor plenum runs.
Companion non–plenum version – Non–plenum equivalent identified as 2412FS for projects that require coordinated cabling types (sold separately).
The Belden CAT6+ Shielded Plenum Data Cable (Belden 2413FS) is an enterprise-grade F/UTP plenum cable engineered for demanding network installations where reliability, signal integrity, and code compliance are all critical. Bonded pairs, a patented central X-spline separator, full aluminum/poly laminate shielding, and a Flamarrest low-smoke CMP jacket work together to deliver exceptional crosstalk control and stable performance across long runs in commercial, broadcast, and data center environments. Supplied in a 1000-foot pull box.
Features
Cat6+ F/UTP plenum cable with bonded pairs and patented X-spline separator for superior crosstalk performance
CMP Flamarrest low-smoke PVC jacket tested to NFPA 262, UL 910, FT6, and IEC 60332-1-2 for air-space use
100% aluminum/poly laminate shield with 24 AWG drain wire for outstanding EMI/RFI rejection
UL Verified Category 6; NEC/CEC CMP compliant; RoHS and California Prop 65 certified
0.285-inch diameter; max 25 lb pulling tension; 1000-foot pull box weighing approximately 49 lb
In the Box
1 x 1000 ft box of Belden 2413FS CAT6+ Shielded Plenum Data Cable, white
High–performance data networking, including simultaneous parallel transmission protocols
Performance & Features
Crosstalk Optimization
Central spline separates pairs to keep pair geometry consistent and reduce crosstalk
Signal Balance
Designed for balanced transmission characteristics to support parallel data transmission methods
Performance Assurance
Engineered to meet Category 6 requirements for insertion loss, crosstalk, and other key parameters, helping maintain bandwidth and network uptime
Installation Durability
Bonded-pair construction withstands higher pull forces and tighter bends than standard twisted pairs
Outdoor Installation Convenience
Dry-core indoor/outdoor and outside-plant plenum designs avoid messy gels, tapes, or powders for moisture protection
Conductors
Conductor Gauge
23 AWG
Number of Pairs
4 pairs
Conductor Construction
Solid
Conductor Material
Bare copper (BC)
Insulation & Shielding
Insulation Material
Fluorinated ethylene propylene (FEP)
Overall Shield Material
Polyester plus aluminum/polyester bi-laminate
Shield Coverage
100% overall coverage
Drain Wire
24 AWG solid tinned copper drain wire
Cable Construction
Overall Cable Diameter (Nominal)
0.285 in (7.24 mm)
Outer Jacket Material
Flamarrest® low-smoke PVC
Outer Jacket Nominal Diameter
0.285 in (7.24 mm)
Ripcord
No ripcord
Fillers
Patented central X-spline
Separator Material
Polyester tape
Mechanical
Bulk Cable Weight
49 lbs per 1000 ft
Maximum Recommended Pulling Tension
25 lbs
Minimum Bend Radius (Operation)
1 in (minor axis)
Minimum Bend Radius (During Installation)
3 in
Temperature Ratings
Storage Temperature Range
-20°C to +75°C
Installation Temperature Range
+5°C to +50°C
Operating Temperature Range
-20°C to +75°C
Standards & Compliance
NEC / UL Rating
Article 800, CMP
CEC / c(UL) Rating
CMP
Telecommunications Standard
Category 6, TIA 568.C.2
UL Verification
Verified to Category 6 performance
Flame Test Compliance
NFPA 262, UL 910 (Plenum), FT6, IEC 60332-1-2
China RoHS (MII Order #39)
Compliant
California Proposition 65
Yes
Non-Plenum Companion Part Number
2412FS
Safety & Regulatory Notices
Prop 65 Warning
WARNING: This product may expose you to chemicals which are known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
WARNING: This product may expose you to chemicals which are known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
If you want to share this elsewhere, you can click the link below to copy it